Welcome to Part Two of winter hat making!
In Part One, we made three hats using Pattern A:
In Part Two, we will be making three hats using Pattern B:
which, upon cutting on the fold,
produces this full piece of fabric:
Like Pattern A, this pattern was drafted by measuring around my kids' heads
and dividing the circumference by six, to get the width of the panels that manifest as those six pointy bits at the top of the pattern. The two lower bulges of the pattern are the integrated ear flaps.
You can read the sewing notes and tips in Part One but here is a quick reminder for layout:
Let's begin. Pattern B is similar to Pattern A in that it is made of six equal parts.
However, it differs in that it utilizes darts to shape the rounded top instead of entire seams running the length of the hat.
Start out by making the fancy embellishments (see Part One for more detailed instructions).
Then sew up the darts in both the outer fleece layer and the knit lining layer. Don't forget to leave a hole in one of the lining darts for turning out later!
Now attach the braids, upside down, to the RS of the outer fleece ear flap (shown), as well as the pompom to the apex (not shown - see Part One for instructions).
Then stuff the outer fleece layer into the lining layer, RS together, lining up the ear flaps and center back seams. Sew around the bottom hem (which goes around the face, neck and ear flaps) of the hat to attach both layers together.
Turn right side out through the hole in the lining, stitch the hole shut and stitch together both hat layers at the top point where all the darts meet.
Here are both sides of the hat -outside and lining-side. Yes- theoretically reversible, except the pompom makes wearing the hat inside out a bit uncomfortable.
The integrated ear flap is optional - just as we added ear flaps to one of the variations of Pattern A in Part One, we can also omit the ear flaps in Pattern B to get this bunny version, inspired by a hat I saw in an old Hanna Andersson catalog:
Note that this hat could have been made with Pattern A, except I didn't want seam lines running through the face of the bunny. Pattern B allowed for a smooth face for embroidering facial details
while still allowing the insertion of ears and bobtail into the darts and center back seam, respectively:
Two things were done to Pattern B to make it bunny-hat-ready:
- The ear flaps were completely sliced off to make a smooth bottom hem.
- The lining hem was lowered by 1" (so that the whole hat lining is 1" longer than the outer fleece hat). That extra 1" was for wrapping around to the outer side of the hat to make the contrast self-bound trim. Again, this is optional but I wanted a little more color against the otherwise very plain white hat.
Otherwise, the construction method was exactly the same as that first purple hat -
- Sew outer and lining darts closed, inserting tail and ears where desired.
- Embroider details on outer hat.
- Place outer hat in lining hat, RS together, lining up their circumference edges.
- Sew both layers together around their circumference.
- Turn entire hat right side out through hole in lining.
- The lining, being longer than the outer hat, will wrap over the hem of the outer hat to make an edging that is the same width as the seam allowance you gave. Stitch in the ditch as shown in the photo above, to keep the hem in place.
- Finish the hat: stitch the lining hole closed etc.
And just so you know that I can live with sewing imperfections - see that wrinkle in the pink binding right in the front of the hat? It's not a fancy ruffle, OK? The lining was one of those unstable 4-way stretch jerseys, and its circumference was a little bigger than the outer fleece circumference. So it sheared while I was sewing it and I was too tired to unpick the whole thing, take in the ease at the center back seam and... well, you get the idea.
This third hat is identical to the first hat worn by Jenna, except that it has bound edges. (Also applique, which is kinda obvious but it's just embellishment and not significant to the construction process).
- the two hat layers, after having their darts sewn closed, are sewn together with their WRONG sides touching.
- there is no turning-right-side-out so you don't need to leave a hole in the lining.
- you are binding around the actual finished edge of the hat circumference, so you don't need a seam allowance around the bottom edge of the hat.
- the braids need to be attached differently in order to accommodate the binding.
In the photo below, you can deduce the sequence of sewing that bottom edge:
- Sew both hat layers together, WS touching.
- Sew the braid to the lining side of the ear flap, upside down.
- Sew the RS of the knit binding to the lining layer on top of the braid. See this post for a tutorial on how to bind with knit.
4. Flip the binding to the outer side of the hat, fold in like bias tape, and sew all around the hat edge.
5. The photo on the left shows the lining side of the hat, with the braid neatly attached, but pointing up. Flip the braid down, like in the right photo
This is the hat, outer side out.
This is the hat turned lining-side out. Again, theoretically reversible if you don't mind the pompom digging into the top of your head.
Yes- definitely much more sensible this way out. Do you see that center front seam? My hat has that because I didn't have a large enough bit of grey fleece to cut the whole hat in one piece. It had to be done in two pieces and joined at both the front and back center seams.
In addition to these three hats, here is a fourth hat using Pattern B, which I didn't actually sew. It's a good design for smaller kids who can't seem to keep their hats on their heads. If you narrow and extend the ear flap, you can turn it into a chin strap that fastens with velcro or a snap. You'll have to measure around your child's head in the relevant orientation to get the actual length of the strap needed.
And now, here are the pattern templates.
1. I made them in two sizes:
- Size 1 fits head circumferences of about 20" (Kate).
- Size 2 fits head circumferences of 21" - 21.5" (Jenna and Emily).
Don't ask me for age sizes. Stuff like 3T or 7-8 or Medium mean zilch to me. I mean, look - Jenna and Emily, who are 2 years apart in age, have the same hat size. Only actual body dimensions mean anything to me when I'm sewing. So go measure your children's heads and choose the size that works best and/or take in or let out a fraction of an inch in the seams where you need it.
2. My patterns have NO SEAM ALLOWANCES. You must add your own seam allowances.
3. Included in the pdf document is a cutting sheet for the six hats I made
and here are the schematic diagrams for the remaining two hats that I didn't make:
So eight hats from two patterns in two sizes, but you can easily, easily adapt them to make other designs. I considered a making myself a beanie in charcoal and black and with hand-embroidery but got bored before I even drafted the pattern in my size. There are other projects to move on to! And a new tutorial series coming up!